Number of Articles: 530
1. Multi layered finite element analysis of graded coatings in frictional rolling contact

Volume 8, Issue 1, Winter 2015, Pages 1-12

R. Jahedi; S. Adibnazari


2. Design of Optimal PID, Fuzzy and New Fuzzy-PID Controller for CANSAT Carrier System Thrust Vector

Volume 8, Issue 2, Spring 2015, Pages 1-9

A. Kosari; H. Jahanshahi; A. A. Razavi


3. Experimental Investigation of the Flow Control of Wake Cylinder by a Plate with Different Geometrical Ends

Volume 9, Issue 2, Spring 2016, Pages 1-10

A.B. Khoshnevis; AmirReza Mamouri; AmirReza Mamouri; V. Barzenoni


4. Kinematic Synthesis of a Novel Parallel Cable Robot as Artificial Leg

Volume 9, Issue 3, Summer 2016, Pages 1-10

Ebrahim Shahabi; MirAmin Hosseini


5. Influence of Vibratory Finishing Process by Incorporating Abrasive Ceramics and Glassy Materials on Surface Roughness of CK45 Steel

Volume 9, Issue 4, Autumn 2016, Pages 1-6

Payam Saraeian; Mostafa Gholami; Amir Behagh; Omid Behagh; Hamid Reza Javadinejad; Mohammad Mahdieh


6. Longitudinal and Lateral Vibration Analysis of Cables in a Cable Robot Using Finite Element Method

Volume 10, Issue 1, Winter 2017, Pages 1-11

Hami Tourajizadeh; Mahdi Yousefzadeh; Moharram Habibnejad Korayem


7. Behavior Analysis of Cold Expanded-Bolt Clamped AL2024-T3 Plate

Volume 10, Issue 2, Spring 2017, Pages 1-13

M. Sayah Badkhor; A. R. Naddaf Oskouei*; H. Mohammadi Hooyeh; F. Shirbakht


8. Evaluation of Parameters Affecting Magnetic Abrasive Finishing (MAF) of Superalloy Inconel 718

Volume 10, Issue 3, Summer 2017, Pages 1-10

Mehrdad Vahdati; SeyedAlireza Rasouli


9. Workspace Analysis of 2-PR(Pa)U- 2-PR(Pa)R New Parallel Mechanism

Volume 10, Issue 4, Autumn 2017, Pages 1-6

Mehran Mahboubkhah; Sajjad Pakzad


12. Investigating the Effect of Cutting Condition on the Plastic Energy in Turning Process of AISI 1050

Volume 12, Issue 3, Summer 2019, Pages 1-8

Mohammad Meghdad Fallah; Seyyed Reza Hamzeloo


13. Investigating the Performance of Coated Carbide Insert in Hard Steel Helical Milling

Volume 11, Issue 3, Summer 2018, Pages 1-9

Navid Molla Ramezani; Behnam Davoodi; Mojtaba Rezaee Hajideh


14. Modelling of Friction Stir Extrusion using Artificial Neural Network (ANN)

Volume 11, Issue 4, Autumn 2018, Pages 1-12

Mohammad Ali Ansari; Reza Abdi Behnagh; Dong Lin; Sarang Kazeminia


15. Direct Kinematics Solution of 3-RCC Parallel Robot using a Semi-Analytical Homotopy Method

Volume 12, Issue 1, Winter 2019, Pages 1-12

Seyyed Mojtaba Varedi-Koulaei; Masoumeh Rahimi


16. Design, Modeling and Adaptive Force Control of a New Mobile Manipulator with Backlash Disturbances

Volume 12, Issue 2, Spring 2019, Pages 1-16

Hami Tourajizadeh; Samira Afshari


17. Multi-Objective Optimization of the Stamping of Titanium Bipolar Plates for Fuel Cell

Volume 12, Issue 4, Autumn 2019, Pages 1-8

Vahid Modanloo; Vali Alimirzaloo; Majid Elyasi


20. Design and Weight Optimization of Pin Loaded Composite Plates

Volume 1, Issue 1, Autumn 2007

Mohamad Alipour; Mahmoud Mehrdad Shokrieh


22. Study of Composite Pressure Vessel CNG with Nonmetal Liner Under Low Velocity Impact

Volume 1, Issue 3, Spring 2008

Abbas Vafaeisefat; Mohammad Tafazoli Harandi


23. On Using the Fourth Order Finite Difference Method in Studying Orthotropic Rectangular Plate's Vibration Behavior

Volume 1, Issue 4, Summer 2008

MohamadHosein Kargarnovin; Kasara Karbaschi; Hasan Hasanzadeh