Volume 15 (2022)
Volume 14 (2021)
Volume 13 (2020)
Volume 12 (2019)
Volume 11 (2018)
Volume 9 (2016)
Volume 8 (2015)
Volume 7 (2014)
Volume 6 (2013)
Volume 5 (2011-2012)
Volume 4 (2010-2011)
Volume 3 (2009-2010)
Volume 2 (2008-2009)
Volume 1 (2007-2008)
1. Workspace Analysis of 2-PR(Pa)U- 2-PR(Pa)R New Parallel Mechanism

Mehran Mahboubkhah; Sajjad Pakzad

Volume 10, Issue 4 , December 2017, Pages 1-6

Abstract
  Parallel kinematic machines, are closed loop structures which have more accuracy, stiffness and ability to withstand high loads. Kinematic of these mechanisms is complicated due to their closed–loop structure, parallel pods, joint constraints and movement constraints. This paper proposes a new ...  Read More

2. Fuzzy-GSA Based Control Approach for Developing Adaptive Cruise Control

M. Bostanian

Volume 10, Issue 4 , December 2017, Pages 7-19

Abstract
  Adaptive Cruise Control (ACC) controls vehicle speed and its distance to the proceeding vehicle in the same lane. In this paper a two-level control architecture is proposed to control both velocity and distance to the leading vehicle by taking advantage of fuzzy logic control (FLC) approach. Then the ...  Read More

3. Experimental Study of the Effect of Impeller Geometrical Parameters on Fluid Hydrodynamics in Copper Solvent Extraction Mixer

S. Parvizi; S. Aosati; E. Keshavarz Alamdari

Volume 10, Issue 4 , December 2017, Pages 21-25

Abstract
  Dynamic mixers are widely used in hydrometallurgical processes. Improvement in mixers’ efficiency is one of the greatest challenges in this research.The geometrical factors of the impeller are of the most important elements affecting hydrodynamics and efficiency. Type, diameter, speed and off-bottom ...  Read More

4. Impact of Energy Dampers in Improvement of Impulsive Response of Double Layer Grids Space Structures

H. Zarrintala; A. Maleki; M. Darvishhashemi

Volume 10, Issue 4 , December 2017, Pages 27-35

Abstract
  The main purpose of the study is to evaluate the effectiveness of these dead-points mono laterally in controlling the space location of the structures against the explosion loading in this regard. For the reason, nonlinear dynamical analyses on three kinds of structures under two layers’ space ...  Read More

5. Mechanical Design and Simulation of a Saddle-Assistive Device for Sit-to-Stand Transfer in Healthy Subjects

A. Hojjati Najafabadi; S. Amini; F. Farahmand

Volume 10, Issue 4 , December 2017, Pages 37-44

Abstract
  Assistive device equipment can improve the performance of sit-to-stand (STS), standing, and walking of people with lower limb disability. The motorized assistive device is usually expensive and the use of another assistive device also makes an excessive force in the upper and lower extremity during (STS) ...  Read More

6. Genetic Algorithm and ANN for Estimation of SPIV of Micro Beams

M. Heidari

Volume 10, Issue 4 , December 2017, Pages 45-54

Abstract
  In this paper, the static pull-in instability (SPIV) of beam-type micro-electromechanical systems is theoretically investigated. Herein, modified strain gradient theory in conjunction with Euler–Bernoulli beam theory have been used for mathematical modeling of the size dependent instability of ...  Read More

7. Synthesis of B4C - Nano TiB2 Composite Nano Powder by the Chemical Precipitation Method

M. Saeedi Heydari; H. R. Baharvandi

Volume 10, Issue 4 , December 2017, Pages 55-61

Abstract
  The aim of this research is to determine the proper concentration of Titanium Tetra IsoPropoxide (TTIP) and select the right temperature and time of calcinations for the synthesis of B4C-nano TiB2 composite Nano powder by the chemical precipitation method. For this purpose, first, solutions with TTIP ...  Read More

8. Modeling and Design of a Disk-Type Furrow Opener’s Coulter Its Mechanical Analysis and Study for No-Till Machinery (Combination and Bertini)

J. Ghezavati; M. Abbasgholipour; B. Mohammadi Alasti; A. Shirneshan; A. Shadkam

Volume 10, Issue 4 , December 2017, Pages 63-73

Abstract
  No-till practices play an important role in decreasing production costs, increasing soil organic matter content, improving soil structure and removing unwanted environmental impacts. However, due to a lack of access to proper machinery for direct seeding in unplowed lands, such practices have failed ...  Read More

9. Estimation of Surface Roughness in Turning by Considering the Cutting Tool Vibration, Cutting Force and Tool Wear

A. Salimi; A. Ebrahimpour; M. Shalvandi; E. Seidi

Volume 10, Issue 4 , December 2017, Pages 75-83

Abstract
  Surfacequality along with the low production cost, play significant role in today’s manufacturing market. Quality of a product can be described by various parameters. One of the most important parameters affecting the product quality is surface roughness of the machined parts. Good surface finish ...  Read More

10. Stress and Displacement Analysis of First Molar Hollow Tooth during Dental Filling Operation using Three-Dimensional Finite Element Method

M. R. Karamooz-Ravari; B. Shahriari; E. Seyfali

Volume 10, Issue 4 , December 2017, Pages 85-90

Abstract
  the amount of rotten tooth that is come out of teeth is an important issue in dental filling because of its effects on strength of teeth. The main goal of this study is to determine a criterion for the amount of rotten tooth which can be brought out. To do so, first, a three-dimensional finite element ...  Read More

11. Fabrication of AA1060/Al2O3 Composites by Warm Accumulative Roll Bonding Process and Investigation of its Mechanical Properties and Microstructural Evolution

M. Heydari Vini; P. Farhadipour

Volume 10, Issue 4 , December 2017, Pages 91-98

Abstract
  Recently accumulative roll bonding (ARB) has been used as a novel method to produce particle reinforced metal matrix composites. The accumulative roll bonding as a severe plastic deformation (SPD) rolling procedure aimed at enhancing the mechanical properties of metals and alloys. The process consists ...  Read More